Blaupunkt TRIER RCR 126 User Manual

Radio / Cassette  
Trier  
RCR 126  
Operating instructions  
Contents  
Short instructions ........................ 17 Scanning stations with Radio-Scan ...... 24  
Selecting the seek tuning sensitivity ..... 24  
Switching from stereo to mono (FM) ..... 24  
Important notes ............................ 20  
Precautions ........................................... 20  
Traffic safety ......................................... 20  
Installation/Connection.......................... 20  
Receiving traffic programme  
stations with RDS-EON ................ 25  
Traffic announcement priority on/off ..... 25  
Warning beep........................................ 25  
Switching the warning beep off.......... 25  
Automatic seek tuning start................... 25  
Adjusting the volume for traffic  
KeyCard theft-protection system 21  
Putting the unit into operation ............... 21  
Removing the KeyCard ......................... 21  
“Defining” a second KeyCard/  
announcements and the warning beep . 25  
Replacing a KeyCard ............................ 21  
Displaying the radio pass data .............. 21  
Optical indication for extra security ....... 22  
Tape operation.............................. 26  
Inserting a tape ..................................... 26  
Removing a tape ................................... 26  
Fast Forward/Rewind ............................ 26  
PROG selector ...................................... 26  
Radio operation with RDS ........... 22  
AF - Alternative frequency .................... 22  
REG - regional programme ................... 22  
Automatic tuning ................................... 23  
Manual tuning ....................................... 23  
Scrolling through the broadcasting  
DSC programming........................ 27  
Overview of the DSC factory settings ... 28  
network (only FM) ................................. 23  
Changing the memory bank .................. 23  
Storing stations ..................................... 23  
Automatically storing the strongest  
stations with Travelstore ....................... 24  
Recalling stored stations ....................... 24  
Sampling stored stations briefly  
Appendix ....................................... 28  
Care notes ............................................ 28  
Mechanism/cassette tapes ................ 28  
Specifications ........................................ 28  
(Preset Scan) ........................................ 24  
16  
Short instructions  
1 On  
Volume  
Off  
2 LD  
Loudness - When listening at a low  
GEO –  
To adjust the balance (left/right) and  
fader (front/rear) with the rocker switch.  
level, the Loudness function creates a  
more natural sound by boosting the low  
frequency range.  
To switch the Loudness on/off:  
Press LD.  
For more information, read chapter  
“DSC programming”.  
This unit can also be switched on and  
off with the KeyCard B.  
Also, when being connected correctly,  
you may turn the radio on and off via  
the ignition of your car.  
Fader front  
Fader rear  
Balance left  
Balance right  
3 AUD/GEO  
AUD –  
Use one of the following possibilities to  
continue operating the set when the  
ignition is switched off:  
a) Switch on/off with knob 1.  
b) Remove/insert the KeyCard.  
c) Press AUD 3.  
When turning on the unit with the Key-  
Card or by pressing the AUD button,  
the system will start to play with the  
volume adjusted last.  
When operating the unit with the igniti-  
on being switched off, the system will  
automatically shut down after one hour  
in order to avoid that the battery goes  
flat.  
To adjust the treble and bass frequen-  
cies with the rocker switch.  
To alter a setting,  
press AUD or GEO and then chan-  
ge the value with the rocker switch.  
The adjusted value is indicated in the  
display.  
The last setting will be stored automati-  
cally.  
To finish the setting: Press AUD or  
GEO.  
If the setting remains unchanged within  
8 seconds, the display will switch back  
to the previous condition.  
Treble +  
Treble –  
Bass –  
Bass +  
17  
4 DSC (Direct Software Control)  
Use the DSC function to customise  
certain programmable, basic settings to  
suit your personal needs and prefe-  
rences. See chapter “DSC pro-  
7 lo/dx  
To alter the automatic seek tuning sen-  
: Display  
Radio operation:  
sitivity.  
If “lo” is displayed, the radio will only  
pick up strong, local stations (low sensi-  
tivity).  
gramming” for more information.  
NDR1 NDS - Station abbreviation or  
frequency  
If “lo” does not light up, the radio will  
also pick up weaker, distant stations  
(high sensitivity).  
To switch over: Press lo or dx briefly.  
For more information, see chapter  
“DSC programming”.  
5 AF - Alternative frequency during RDS  
operation  
FM  
T
5
- Waveband  
- Memory bank (I, II, T)  
- Preset button (1 - 6)  
- Stereo  
When “AF” lights up in the display, the  
radio will automatically search for a  
frequency offering better reception of  
the same RDS programme.  
lo  
- Seek tuning sensitivity  
- Alternative RDS frequency  
- Traffic programme identifier  
- Priority for traffic programme  
stations  
AF  
TP  
TA  
To switch AF on/off: Press AF briefly.  
8 Cassette removal  
Press  
.
6 REG  
LD  
- Loudness  
REG ON / REG OFF  
9 Cassette loading slot  
Insert tape (side A or 1 up; the open  
side facing to the right).  
With REG ON the system will only  
switch to a better alternative frequency  
if the latter belongs to a linked station  
offering the same regional programme  
(see “REG - regional programme).  
To switch REG on or off: Press REG  
until “REG ON” or “REG OFF” appears  
in the display (BEEP tone).  
Tape operation:  
TR1--PLAY - Side 1 (or 2)  
18  
; PROG button/Fast winding  
> 1, 2, 3, 4, 5, 6 - preset buttons  
You can store six stations on each FM  
memory bank (I, II, T).  
A FM  
To select one of the FM memory banks  
To switch to the other side of the  
cassette tape:  
Press both buttons simultaneously.  
The display shows TR1-PLAY or TR2-PLAY.  
I and II.  
To store a station: Press button during  
radio operation and hold down until the  
radio resumes play.  
To change the memory bank:  
Press button until the desired level is  
indicated in the display.  
To recall a station: Select the wave-  
band and on FM also the desired me-  
mory bank (press FM or TS button as  
many times as required). Then press  
the corresponding preset button briefly.  
B KeyCard theft-protection system  
To operate the set it is necessary that  
you have inserted the KeyCard.  
Fast winding  
FR : Fast rewind; stop by pressing FF.  
FF : Fast forward; stop by pressing FR.  
? TA (priority for traffic announcements)  
If “TA” is displayed, the system will play  
traffic stations only.  
KeyCard  
TA on/off: Press button.  
For this, introduce the KeyCard into the  
slot with the contact area showing up  
(KeyCard tongue pulled out).  
Read also the information under “Key-  
Card theft-protection system”.  
< SC  
Radio operation  
Scan (sampling all stations to be recei-  
ved): Press SC briefly.  
@ TS - Travelstore  
To store the six most powerful stations  
automatically with Travelstore:  
Store: Press TS until seek tuning starts  
in the display.  
Recall: Press TS, “T” is indicated in the  
display. Then briefly press one of the  
presets 1, 2, 3, 4, 5, 6.  
= PS  
Flashing KeyCard tongue  
Preset Scan (sampling all stations  
stored on the preset buttons): Press PS  
briefly.  
When the car radio is turned off, the  
KeyCard tongue can be switched to  
flash for extra anti-theft protection. This  
feature can be switched on and off via  
DSC - LED.  
19  
Important notes  
Precautions  
C Rocker switch  
Installation/Connection  
Seek tuning  
Before starting to use your new car radio,  
please read the information on “Traffic safe-  
ty” and “KeyCard theft-protection System”  
carefully.  
If you would like to install this equipment  
yourself or add any new components, please  
read the enclosed installation and connec-  
tion instructions carefully.  
Do not connect the loudspeaker outputs to  
ground!  
Use only the accessory and replacement  
parts approved by Blaupunkt.  
Traffic safety  
Up  
Down  
As the driver of a motor vehicle, it is your  
responsibility to pay attention to the traffic  
situationatalltimes.Neveruseyourcarradio  
in a way that could distract you.  
Please keep in mind that you travel a di-  
stance of 14 m per second at a speed of only  
50 km/h.  
Should the traffic situation become particu-  
larlydemanding,weadviseyounottousethe  
radio.  
Always make sure that you are still able to  
hear any warning signals coming from outsi-  
deofthevehicle, suchaspoliceorfireengine  
sirens, so that you can react accordingly.  
Therefore, youshouldalwaysselectamode-  
rate volume for playing your car radio while  
you are driving.  
/
/
Up/down in short intervals  
(“AF” must be switched off)  
To scroll through the broadcasting  
network when “AF” is activated  
(e.g. NDR1 ... NDR4).  
Extra function:  
In the DSC mode:  
Select and programme  
DSC functions.  
20  
KeyCard theft-protection system  
This car radio is supplied with one KeyCard After approximately 10 seconds, the display  
Press the KeyCard in, which releases  
the card and puts it in the proper positi-  
on for being removed.  
as standard.  
However, the unit can also be operated with When inserting a card of a different kind (like  
a second card. for example a credit card), the display will  
will show “TURN OFF”. Now turn off the set.  
Remove the first KeyCard and insert  
the new one while “CHANGE” is still  
being displayed.  
If you have lost or damaged your KeyCard, show “WRONG KC” for approximately 2 se-  
you can buy a new one from your specialised conds.  
dealer.  
Remove the wrong card and turn off the set.  
Now you can also use the new KeyCard for  
operating your unit.  
When using two KeyCards, you can indivi- Do not make further adjustments until you  
dually store the following functions:  
have a correct KeyCard available.  
Amaximumoftwocardscanbeusedperset.  
When trying to “define” a third one, the sy-  
stem will automatically delete the access  
authorisation of that KeyCard which was not  
used for the “learning” process.  
Bass, treble, balance and fader settings,  
assignments of preset buttons, Loudness,  
TA (traffic announcement volume), BEEP  
volume.  
In addition to this, the settings activated be-  
fore switching the radio off, such as the  
waveband, station, TA priority, Loudness,  
AF, REG ON/OFF and seek tuning sensitivi-  
ty, will also remained stored.  
Removing the KeyCard  
Never pull out the KeyCard directly.  
First press the KeyCard in.  
This releases the card and puts it in the  
proper position for being removed.  
Displaying the radio pass data  
Now you can pull it out.  
You can use the KeyCard supplied with the  
unit to display the individual radio pass data  
such as the model name, the type number  
(7 6 ...) and the serial number:  
Thisensuresthatthebasicsettingsyouhave  
programmed will automatically be activated  
as soon as you have inserted your KeyCard.  
“Defining” a second KeyCard/  
Replacing a KeyCard  
Press and hold down preset buttons  
While operating the unit with the first Key-  
Card, you can “define” a second one to be  
also used with the set:  
1 and 6 while switching on the unit.  
Putting the unit into operation  
Press the TS button within 2 seconds.  
The radio pass data will move through the  
display several times.  
Turn on the set and introduce the Key-  
Card into the slot with the contact area  
showing up (KeyCard tongue pulled  
out).  
Insert the first KeyCard and turn on the  
set.  
To quit the function:  
Press the DSC button and select  
Press any button.  
“LEARN KC” with / .  
The car radio is now ready for operation.  
If a wrong KeyCard is inserted, then “CARD  
ERR” will appear in the display. In this case  
please do not go on operating the set.  
The display will switch to “CHANGE”.  
21  
Radio operation with RDS (Radio Data System)  
Optical indication for extra  
security  
The Radio Data System offers you more stored frequencies, the unit is automatically  
convenience when listening to FM radio sta- searching for an alternative frequency.  
tions.  
“SEARCH” will disappear from the display  
When the car is stationary, the KeyCard  
tonguecanbeswitchedtoflashforextraanti-  
theft security.  
For this, the following requirements must be  
fulfilled:  
Permanent 12 V supply and the + ignition  
lead must be connected correctly (as illustra-  
ted in the installations instructions).  
“LED 1” must be adjusted in the DSC mode.  
Please refer to chapter “DSC programming -  
LED”.  
More and more radio stations have begun to when the alternative frequency has been  
broadcast RDS information alongside their found or after the frequency band has been  
programmes.  
run through completely.  
Assoonasaprogrammehasbeenidentified, If the reception quality of the selected pro-  
the station name including a regional identi- gramme becomes too bad:  
fier, if applicable, will appear in the display,  
for example, NDR1 NDS (regional program-  
me in Lower Saxony, Germany).  
When RDS is activated, the station buttons  
become programme buttons. You now know  
exactly which programme you have tuned  
into, making it easy to find the desired station  
quickly.  
Tune into another station.  
REG - regional programme  
Certain radio programmes are split up at  
times into regional programmes offering lo-  
cal information. The 1st programme broad-  
cast by NDR, for example, offers program-  
mes with different contents in the northern  
statesofGermanySchleswig-Holstein,Ham-  
burg and Lower Saxony at certain times of  
the day. If you are listening to one program-  
me and move to an area where another  
linked regional programme becomes stron-  
ger, the unit will switch to that programme.  
If you wish to continue listening to the first  
programme,  
But RDS offers you further advantages:  
AF - Alternative frequency  
The AF (Alternative Frequency) function  
makes sure that the strongest frequency of  
the currently selected programme is always  
tuned in automatically.  
This function is activated when “AF” appears  
in the display.  
press the REG button.  
“REG ON” appears in the display.  
In order to switch this function on or off,  
press the AF button briefly.  
If you leave the service area of the regional  
programme tuned into, or if you would like to  
takeadvantageofthefullRDSservice,switch  
to “REG OFF”.  
While searching for the strongest reception  
signal, the radio may switch to mute briefly.  
If “SEARCH” appears in the display when  
switching on the radio or recalling one of the  
22  
Press the REG button briefly.  
When holding the right or left part of the Changing the memory bank  
rocker switch pressed down, the frequency  
YoucanshiftbetweenthememorybanksI,II,  
scan is speeded up.  
When active, “REG ON” will be briefly dis-  
played each time the radio is switched on.  
and T to store and recall preset stations.  
Theselectedmemorybankisindicatedinthe  
display.  
Scrolling through the broad-  
Automatic tuning /  
casting network (only FM)  
Press FM or TS until the desired me-  
mory bank lights up in the display  
(press repeatedly if necessary).  
Press / ; the car radio will automati-  
cally search for the next station.  
You can use the << >> buttons to tune in  
stations of your reception area.  
Whenkeepingtheupperorlowerpart  
/
of  
If several programmes of one broadcasting  
network can be received, you can scroll  
through them in forwards direction pressing  
>>, or backwards using the << button, e.g.  
NDR 1, 2, 3, 4, N-JOY (North German broad-  
caster).  
the rocker switch depressed, seek tuning will  
speed up in upwards or downwards direc-  
tion.  
Storing stations  
On FM, you can store six stations on the  
preset buttons 1 to 6 for each of the memory  
banks I, II and T.  
Automatic tuning  
Select the desired memory bank.  
For this it is necessary that the stations have  
beenreceivedatleastonceandthatAFhas  
been activated before (lights up in the dis-  
play).  
For this purpose, you may start Travelstore  
seek operation:  
Tune in a station with the rocker switch  
(either automatically or manually).  
Press the desired preset button until  
the radio resumes play after the muting  
(takes approximately 2 seconds, confir-  
med by beep).  
Up  
Down  
Press TS for 2 seconds; the system  
starts to run through the frequency  
band.  
/
/
Up/down in short intervals  
(“AF” must be switched off)  
To scroll through the broadcasting  
network when “AF” is activated  
(e.g. NDR1 ... NDR4).  
Now the station has been stored.  
Theactivatedpresetbuttonisindicatedinthe  
display.  
If “AF” does not light up,  
press AF.  
With this, the requirements for selecting sta- Notice:  
tions with << >> are fulfilled.  
Should you tune in a station which has alrea-  
Manual tuning << >>  
dy been stored before, the corresponding  
presetbuttonandthememorybankwillbriefly  
flash in the display if you have selected  
another memory bank.  
(prerequisite: AF is switched off!)  
Press << >>; the frequency will change  
in short intervals in downwards or up-  
wards direction.  
23  
Automatically storing the stron-  
gest stations with Travelstore  
Press PS.  
The radio will briefly play all the stored  
stations one after another.  
Selecting the seek tuning sensi-  
tivity  
You can automatically store the six most  
powerful FM stations of your current recepti-  
on area sorted according to their signal  
strength. This function is particularly conve-  
nient on longer trips.  
You can alter the automatic seek tuning  
sensitivity.  
The system will sample the stations of one of  
the memory banks I, II, or T, depending on  
which bank was selected before. Free preset  
buttons will be skipped.  
If “lo” is displayed, the radio will only pick up  
strong, local stations (low sensitivity).  
If “lo” does not light up, the radio will also pick  
up weaker, distant stations (high sensitivity).  
To switch over,  
To switch off Preset Scan:  
Press the TS button for more than  
Press PS once again.  
The radio will continue to play the cur-  
rently sampled station..  
2 seconds.  
Press lo or dx.  
The radio will search for the strongest FM  
stations and store them on the memory bank  
T (Travelstore). When this process has been  
completed, the radio will play the first station.  
If desired, stations can also be stored manu-  
ally on the Travelstore bank (see “Storing  
stations”).  
On top of this, the sensitivity levels can be  
adjusted separately for lo and dx (see chap-  
ter “DSC programming”).  
Scanning stations with  
Radio-Scan  
Switching from stereo to mono  
(FM)  
Beginning with the station currently tuned in,  
you can scan the waveband. The radio will  
play each station for 8 seconds.  
To start the scan:  
If reception is poor, you may get better sound  
quality by switching to mono:  
Recalling stored stations  
Press SC briefly.  
You can recall any stored station by pressing  
the corresponding preset button.  
Press the lo button for approximately 2  
seconds.  
The scanned frequency or the station  
name will start flashing in the display.  
During the actual scanning process  
“SCAN” will be displayed.  
Select the waveband using FM or TS.  
With mono playback, the stereo sign  
will disappear from the display.  
Briefly press the corresponding preset  
button.  
Each time the radio is switched on, stereo  
playback is activated.  
The unit will automatically switch to mono if  
the received signal is not strong enough for  
stereo playback.  
To select a station currently being scan-  
ned and switch off the scan function:  
Sampling stored stations briefly  
(Preset Scan)  
Press SC briefly.  
If no station is selected, the scan function will  
be automatically switched off after the fre-  
quency band has been run through comple-  
tely. The unit will tune in the station listened  
to before starting the scan.  
With this function you can briefly sample all  
PS stations.  
24  
Receiving traffic programme stations with RDS-EON  
Many FM broadcasters offer traffic messa- Traffic announcement priority  
ges for their service area at regular intervals. on/off  
b) Switch off the priority for traffic an-  
nouncements:  
All traffic programme stations transmit a spe-  
If the priority for traffic announcement pro-  
cial carrier signal alongside their program-  
grammes is activated, “TA” will light up in the  
mes, which is decoded by your car radio. If  
display.  
Press TA.  
“TA” will disappear from the display.  
this signal is identified, “TP” will appear in the  
To switch the priority on or off:  
Automatic seek tuning start  
(tape operation)  
display (Traffic Programme).  
Press the TA button.  
In addition to these, there are also stations  
which do not actually transmit traffic pro-  
grammes themselves, but by using RDS-  
EON they offer the possibility to receive the  
traffic messages broadcast by another traffic  
programme station in the same radio net-  
work. If you listen to one of these stations  
(e.g. NDR3), “TP” will appear in the display  
provided the priority for traffic programme  
stationshasbeenactivated, i.e. “TAmustbe  
displayed.  
If a traffic announcement is broadcast, the  
radio will automatically switch to the linked  
trafficprogrammestation(inthiscase,NDR2)  
for the duration of the message and return to  
the original programme (NDR3) afterwards.  
When pressing TA while a message is being  
broadcast, this message will be interrupted.  
The unit will then switch back to the previous  
condition. The priority for other traffic messa-  
ges remains active.  
When leaving the reception area of the tuned  
in traffic programme station while listening to  
a tape, the system will automatically start  
searching for a new TA programme.  
If no such station is found within approxima-  
tely 30 seconds, tape operation will be stop-  
ped and a warning beep will sound.  
To switch the warning beep off, proceed as  
described above.  
Warning beep  
If you leave the reception area of the traffic  
programme station currently tuned into, you  
will hear a warning beep after approximately  
30 seconds.  
This alarm tone will also be released when  
pressing a preset button which has no traffic  
programme allocated to it.  
Adjusting the volume for traffic  
announcements and the warning  
beep  
This volume was preset at the factory.  
YoucanalterthevalueusingtheDSCfunction  
(see “DSC programming, TA VOL”).  
Switching the warning beep off  
a) Tune into another station offering traffic  
information:  
Press the rocker switch or  
a preset button which has a traffic  
programme station allocated to it.  
Alternatively:  
25  
Tape operation  
Inserting a tape  
Fast Forward/Rewind  
PROG selector  
(To change the tape direction during  
cassette playback)  
Fast Forward  
Turn on the set.  
Insert a tape.  
Press FF.  
At the end of a tape side, the mecha-  
nism changes directions automatically  
to play the other side.  
Press FR and FF simultaneously.  
At the end of a tape side, the mechanism  
changes directions automatically to play the  
other side (Autoreverse). The display shows  
“TR1-PLAY” for track (side) 1 or A or “TR2-  
PLAY” for track 2 or B.  
Insert the tape with side A or 1 showing up, the  
open side facing to the right.  
Stopping Fast Forward operation  
Press FR.  
Fast Rewind  
= Press to eject the tape.  
Notice:  
Press FR.  
Ifthereistoomuchtensiononthetapeduring  
playback, the set may switch over by itself  
before having reached the end of the tape  
side. In this case check the condition of the  
cassette tape. Sometimes it helps to rewind  
it completely.  
At the beginning of the tape, the me-  
chanism will automatically start play-  
back.  
The tape will be played in the direction used  
last.  
“TR1-PLAY” in the display means that track  
1 or A is being played.  
Stopping Fast Rewind operation  
Press FF.  
Removing a tape  
To switch to the other side of the  
cassette tape:  
Press  
.
The cassette will eject.  
Press both buttons simultaneously.  
The display shows TR1-PLAY or TR2-PLAY.  
Fast winding  
FR : Fast rewind; stop by pressing FF.  
FF : Fast forward; stop by pressing FR.  
26  
DSC programming  
DSC (Direct Software Control) allows you to  
customise certain programmable, basic set-  
tings to suit your personal needs and prefe-  
rences and then store them.  
The basic settings for this audio equipment  
weremadeatthefactory. Inthefollowingyou  
canfindanoverviewofthesesettings,sothat  
you can always reset to these if desired.  
If you wish to alter any of the programming,  
TA VOL  
To adjust the traffic an-  
nouncement volume from  
between 1 to 9. The mes-  
sage will then come  
through at this volume.  
(1 = low)  
LOUD  
Loudness - When listening  
at a low level, the Loud-  
ness function creates a  
more natural sound by  
boosting the low frequency  
range.  
LOUD 1 - Low boost  
LOUD 6 - Max. boost  
BEEP  
Confirmation tone for all  
functions which require a  
button to be pressed for  
more than 2 seconds.  
The volume can be adju-  
sted from between 0 to 9.  
(0 = off)  
Each alteration of this va-  
lue is confirmed by a beep  
tone of the corresponding  
volume.  
press DSC.  
RM  
(Radio Monitor)  
The display will show you the adjusted con-  
dition.  
Usetherockerswitchtoselectandadjustthe  
functions described in the following.  
With RM-ON, the unit will  
automatically switch to the  
tuner whenever the casset-  
te is fast winding.  
RM-OFF - The function is  
switched off.  
LOCAL  
(lo)  
To adjust the seek tuning  
sensitivity for local recepti-  
on.  
LED (code)  
You can adjust the LED B  
to flash for extra anti-theft  
protection.  
/
Select function  
Adjust value –  
Adjust value +  
LOCAL 1 - high sensitivity  
LOCAL 3 - low sensitivity  
LED 1 - LED always flash-  
es when the unit  
has been swit-  
DIS  
(dx)  
ched off via the  
ignition.  
To adjust the seek tuning  
sensitivity for distant recep-  
tion.  
LED 0 - No flashing.  
DIS. 1- high sensitivity  
DIS. 3- low sensitivity  
27  
Appendix  
LEARN KC  
To “define” a second Key-  
Card for use with the set.  
Please read the information  
under “KeyCard theft-pro-  
tection system”.  
Specifications  
Care notes  
Amplifier  
Output power:  
Mechanism/cassette tapes  
4 x 20 W RMS power  
acc. to DIN 45324  
(14,4V),  
To avoid possible problems, you should not  
use cassette tapes longer than 60 or 90  
minutes (C60/C90). Store your tapes in a  
cool place away from dirt, dust and tempera-  
turesexceeding50° Celsius. Allowverycold  
4 x 30 W max. power  
To quit the DSC programming mode and  
store the adjustment:  
tapes to warm up before playing them in FM waveband  
Press DSC.  
order to avoid uneven tape transport. After  
approximately 100 hours of use, dust partic-  
les collected on the playback head or roller  
may lead to tape run problems and sound  
distortions.  
Sensitivity:  
1,0 µV at 26 dB  
signal-to-noise ratio  
If the setting remains unchanged within 8  
seconds, the system will automatically store  
the last adjustment. The display will switch  
back to the previous condition.  
Frequency  
response:  
35 - 16 000 Hz  
35 - 16 000 Hz  
Use a head cleaning tape to remove normal  
dirt build-up. For tougher cases, use a cotton  
swab (Q-Tip) soaked with alcohol. Do not  
attempt to clean by inserting a hard object  
into the player!  
Tape player  
Frequency  
response:  
Overview of the DSC factory  
settings  
TA VOL  
BEEP  
: 4  
: 3  
LED (Code) : 1  
LOUD  
RM  
LOCAL  
: 4  
: OFF  
: 1  
DIS  
: 1  
Subject to modifications!  
28  
Blaupunkt-Werke GmbH  
Bosch Gruppe  
8/96  
K7/VKD 8 622 400 772  

Bassworx BA500 1D User Manual
Braun MR 500 CA User Manual
Burnham SCG 1100 H4 User Manual
Canon EF Lens 4412B002 User Manual
H2O Audio Capture iN5 BK User Manual
Hitachi HV D25 User Manual
JVC Car Stereo System KD R610 User Manual
JVC GR AX610U User Manual
JVC GR AXM100 User Manual
JVC GR D93 User Manual